Tutorial flash hp cina dengan z3x box
Hal yg di siapkan solder , kabel rj45 8pin

1.potong rj 45

2 solder pin1 untuk vbat

3 solder pin 2 untuk rx

4 solder pin 3 untuk tx

5 solder pin 8 untuk gnd

6 box z3x tentunya

7 buka mtk tool z3x

8 propile generic mtk

9 READ WRITE FORMAT DLL TEKAN ON/OFF , KLO INI PASTI SUDAH PAHAM SEMUA

10 terserah anda mau apa aja z3x goyang ngebor

11 siapkan nota tulis terserah anda.

INI LOG NYA MITO 303

Gemalto Card Tests Ok!

Selected model is:Generic MT62XX NOR:AUTO

Press Connect to detect memory config...

Updating Flash Configuration...

Welcome to MTKModule v1.9.0.0 Card S/N:XXXXXXXXCard ver.2.2

BROM.DLL Version :BROM_DLL_v3.1012.00 From 2010/06/05 03:44:46

META.DLL Version :META_DLL_v5.808.00 From 2008/02/22 13:33:14

Detecting Loaders ...

Download Agents Found :7

Ready.

Selected model is:Generic MT62XX NOR:AUTO

Press Connect to detect memory config...

Starting flasher module.... [BOOT_MODE]

Boot filename: C:\Program Files\Z3X\MTK\MTK_AllInOne_DA_1012.bin

Reconnect battery and press power button now!

Getting MCUID...

Booting... You can release power key now!

Project Name: MT6223_S00

[!] Failed to detect RAM (Possible Hardware failure)

NOR Detected : (128Mb+0Kb) [ST] M30L0T7000T0, M36L0T7050T0

NAND Detected : N/A

Advanced detection information:

BBCHIP: "MT6223_S00", EXT_26M

CODE(0x6223), VER(0x8A05), Software(0x8A00)

NOR_ID: "[ST] M30L0T7000T0, M36L0T7050T0"

NOR_ID: 0x0020, 0x88C4, 0x0000, 0x0000

NAND_ID: "NAND_UNKNOWN"

NAND_ID: 0x0000, 0x0000, 0x0000, 0x0000

Detection Done!

Reading NOR : "C:\Program Files\Z3X\MTK\MTKBOOT.TMP", 0x00000000:0x00080000

Operation Done!

Setting NOR buffer size :1000000

PostProcessing Boot File

ROMINFO V4 Structure found!

Ver.:TECHAIN23_08A_F_PCB01_GPRS_MT6223_S00.Q106_S1 0_1_AW_F3_101009.BIN

Platform:Q106_S10.1_AW_F3_101009

Filesystem:00E00000:00200000

This device have no SEC block (Safe for READ/WRITE)

Done!

Starting flasher module.... [READ_MODE]

Reconnect battery and press power button now!

Getting MCUID...

Booting... You can release power key now!

Project Name: MT6223_S00

[!] Failed to detect RAM (Possible Hardware failure)

NOR Detected : (128Mb+0Kb) [ST] M30L0T7000T0, M36L0T7050T0

NAND Detected : N/A

Advanced detection information:

BBCHIP: "MT6223_S00", EXT_26M

CODE(0x6223), VER(0x8A05), Software(0x8A00)

NOR_ID: "[ST] M30L0T7000T0, M36L0T7050T0"

NOR_ID: 0x0020, 0x88C4, 0x0000, 0x0000

NAND_ID: "NAND_UNKNOWN"

NAND_ID: 0x0000, 0x0000, 0x0000, 0x0000

Detection Done!

Reading NOR : "C:\Documents and
Settings\Admin\Desktop\TECHAIN23_08A_F_PCB01_GPRS_
MT6223_S00.Q106_S10_1_AW_F3_101009.BIN", 0x00000000:0x01000000

Operation Done!

Processing flash file

Processing ROM File

ROMINFO V4 Structure found!

Ver.:TECHAIN23_08A_F_PCB01_GPRS_MT6223_S00.Q106_S1 0_1_AW_F3_101009.BIN

Platform:Q106_S10.1_AW_F3_101009

Filesystem:00E00000:00200000

Security:00000000:00000000

Preparing SCAT

All blocks are ready for flashing!

Region #0 'ROM' adress:0x00000000

Updating Flash Configuration...

Done!

Selected model is:Generic MT62XX NOR:AUTO

Press Connect to detect memory config...

Starting flasher module.... [WRITE_MODE]

Formatting after download DISABLED

Reconnect battery and press power button now!

Getting MCUID...

Booting... You can release power key now!

Project Custom Name: TECHAIN23_08A_F

Project ID: Q106_S10.1_AW_F3_101009

Project Name: MT6223_S00

RAM Detected : 32Mb SRAM

NOR Detected : (128Mb+32Mb) [ST] M30L0T7000T0, M36L0T7050T0

NAND Detected : N/A

Advanced detection information:

BBCHIP: "MT6223_S00", EXT_26M

CODE(0x6223), VER(0x8A05), Software(0x8A00)

NOR_ID: "[ST] M30L0T7000T0, M36L0T7050T0"

NOR_ID: 0x0020, 0x88C4, 0x0000, 0x0000

NAND_ID: "NAND_UNKNOWN"

NAND_ID: 0x0000, 0x0000, 0x0000, 0x0000

Detection Done!

Writing Flash...

Operation Done!



[You must be registered and logged in to see this image.]



nb ; bisa juga di kawinkan dg box china biar gak solder rx
tx

use Z3x


PROCEDURE ;


-Open Z3x MST TOOL


-Use SPIDERMAN or GPGdragon as usb PORT

[You must be registered and logged in to see this link.]

-You can also do "RESET TO FACTORY DEFAULT " with this tool

[You must be registered and logged in to see this link.]

-Wait Until Done
[You must be registered and logged in to see this link.]


DONE! [You must be registered and logged in to see this image.]

[You must be registered and logged in to see this link.]



Good Job Z3x!